ulo mounting

 

 

ulo it’s every kind of light you might need..

Discover a multitude of mounting options below.

 

Spec ulo 

Portable Desk




 

 

 

 

 

 

 

 

 

 

 

1.  Insert spring pin into small hole on top of base and secure through the base to the underside of the arm. The back of the arm is supplied with a wire management channel.
2.  Gently place the light bar onto the mounting arm with dome magnet face down.
3.  Plug the light bar cord into your selected power supply.
4.  Remove protective film from lens. The front sensor controls the light level and the back sensor controls the color temperature (CCT).

Application Examples: desk, nightstand, end table

Table Anchor




 

 

 

 

 

 

 

 

 

 

 

1.  Determine desired location of ulo. Anchor is designed to install into stable surfaces between 1/2” and 2 1/4” (13-57 mm) with 8” (208 mm) access behind mounting surface to allow for proper installation. Drill a 7/8” (22 mm) hole and slide table anchor and cord into hole, secure with washer and nut.
2.  Route light bar cord with USB-C connector through arm anchor as shown. Gently place the light bar onto the mounting arm with dome magnet face down.
3.  Assemble the arm anchor by inserting the indicated spring pin into small hole on top of anchor and secure in place through the anchor to the underside of the arm. The channel in the back of the arm is supplied for wire management.
4.  Plug the light bar cord into your selected power supply. Remove protective film from lens. The front sensor controls the light level and the back sensor controls the color temperature (CCT).

Application Examples: desk, library table, work bench

 

Table Clamp




 

 

 

 

 

 

 

 

 

 

 

1.  Insert spring pin into small hole on top of clamp and secure through the clamp to the underside of the arm. The back of the arm is supplied with a wire management channel.
2.  Use the clamp screw to secure assembly to desired surface. The clamp will accommodate a sturdy surface from 1/8” to 2” (3 mm to 50 mm).
3.  Gently place the light bar onto the mounting arm with dome magnet face down.
4.  Plug the light bar cord into your selected power supply. Remove protective film from lens. The front sensor controls the light level and the back sensor controls the color temperature (CCT).

Application Examples: bookshelf, podium, DJ booth

Wall Anchor




 

 

 

 

 

 

 

1.  Determine desired location of ulo. Anchor is designed to install into stable surfaces between 1/2” and 2 1/4” (13-57 mm) with 8” (208 mm) access behind mounting surface to allow for proper installation. Drill a 7/8” (22 mm) hole and slide wall anchor and cord into hole, secure with washer and nut.
2.  Route light bar cord through wall anchor as shown. Gently place the light bar onto the mounting arm with dome magnet face down
3.  Plug the light bar cord into your selected power supply. Remove protective film from lens. The front sensor controls the light level and the back sensor controls the color temperature (CCT).

Application Examples: bedside, reading chair lighting, cubicle partition

Wall Surface*




 

 

 

 

 

 

 

1.  Determine desired location of ulo. Drill 3/32" pilot holes into surface. Slide the canopy down the bracket to allow access to the mounting plate. Mount bracket to desired surface.
2.  Gently place the light bar onto the mounting arm with dome magnet face down
3.  Plug the light bar cord into your selected power supply. Remove protective film from lens. The front sensor controls the light level and the back sensor controls the color temperature (CCT).

Application Examples: bedside, reading chair lighting, cubicle partition  *used in applications where cord can not be recessed into wall.

Mini Mount




 

 

 

 

 

 

 

1.  Surface must be clean, dry and flat. Remove tape backing and install to desired surface.
2.  Gently place the light bar onto the mounting arm with dome magnet face down.
3.  Plug the light bar cord into your selected power supply. Remove protective film from lens. The front sensor controls the light level and the back sensor controls the color temperature (CCT).

Application Examples: computer monitor, work bench, any surface you can stick it to

Shelf Mount




 

 

 

 

 

 

 

1.  Determine desired location of ulo. Drill 3/32" pilot holes into surface. Mount the bracket to desired surface. If using the shim, place between the mounting surface and bracket and using 2” screws. If not using shim, mount bracket directly to surface using 5/8” screws.
2.  Gently place the light bar onto the mounting arm with dome magnet face down.
3.  Plug the light bar cord into your selected power supply. Remove protective film from lens. The front sensor controls the light level and the back sensor controls the color temperature (CCT).

Application Examples: kitchen, bookshelf, lab bench